I'll try to put Win10 to test...
it's at 500mhz... and it's on pin 10, if I change it to 9 it gives an error message when sending the code >764:664
Beiträge von danielvieira
-
-
I already left the tool open for several minutes and it didn't calibrate. I'm using Windows 11 64 bits... I haven't tried it with Windows 10.
everything was downloaded from the vlud website. and I just changed it to 8 mhz
I will have to install Windows 10 to test... 32 or 64 bit version?
Alles anzeigenWell... The 1003 part is for starting coding session 10c0 is for downloading/coding.
Ever tried
>764:664
1003
close serial monitor (otherwise com port is busy, but this works already as you are able to connect to Arduino with tool)
start tool with admin rights and internet (otherwise it will pause working until it's online again)
Connect arduino
access nac
Download parameters
Change parameters (vin on tab "main")
just for testing?
As far as I've read here, you tried with 10c0
If I enter code 1003 it gives an error code upon return and does not go into diagnostic mode. If I put 10C0 it returns code 50C0 and goes into diagnostic mode
-
Hello friend... it didn't work... when I run the Arduino it goes into diagnostic mode but the green bar doesn't run and it exits diagnostic mode in multimedia.
I recorded a short video for you to see
-
hello... friend... 1003 is for nac. the aio of continental south america is 10c0... there is a list of codes on github...
GitHub - ludwig-v/arduino-psa-diag: Arduino sketch to send UDS / KWP diagnostic frames over CAN-BUS to PSA/Stellantis cars (Peugeot, Citroen, DS, Opel)Arduino sketch to send UDS / KWP diagnostic frames over CAN-BUS to PSA/Stellantis cars (Peugeot, Citroen, DS, Opel) - GitHub - ludwig-v/arduino-psa-diag:…github.com -
I had doubts friend... do I connect the Arduino MCP2515 to the car and then I just open the Arduino NAC? without using the Arduino ide to leave the multimedia in diagnostic mode?
-
my canbus is 8mhz... if I leave it at 16mhz it doesn't connect to the Arduino IDE.
This I was using the sketch and libraries that you send. I'll try again by turning off the notebook and just connecting the Arduino NAC to see what happens...
The Arduino MCP2515 has the jumper for 8 MHz and the IDE sketch is also at 8 MHz
friend, one question... do I just use the code >764:664 and then the code 10C0? Do you need another code? Or is it just these two and then I open the Arduino nac
Sometimes Arduino Ide does not allow another application to connect to the same port even when it is turned off. So try to turn off the computer, turn it on again and run Arduino-NAC.exe immediately. Arduino Ide do not start. Have you checked whether your CAN-BUS shield is 8 or 16 MHz? You can see that on the crystal on the shield. You have to enter the right value in the Arduino sketch, otherwise it won't work.
Did you first upload this sketch to Arduino: https://github.com/ludwig-v/ar…diag/arduino-psa-diag.ino
and Libraries: https://raw.githubusercontent.…aries/arduino-mcp2515.zip and https://raw.githubusercontent.…braries/ArduinoThread.zip
friend, one question... do I just use the code >764:664 and then the code 10C0? Do you need another code? Or is it just these two and then I open the Arduino nac
-
Hello friend... that's why I close the Arduino IDE, and I have internet on the notebook when I use the Arduino. the Arduino IDE says it is connected... but the green bar doesn't run...
This is the screen... it stays connected and still my friend... or am I doing something wrong?
-
Hello... when I try to run PSA-Arduino-NAC.exe and click on Arduino connect it doesn't do anything. The green status bar at the bottom doesn't appear...
I send the code >764:664 then the 10C0 code which is from AIO Continental... but I don't know if I have to send any more code or not... I just send these codes and try to open PSA-Arduino-NAC.exe. .. do I need to send more unlock codes? thanks
-
Continental's AIO has a memory lock and is not accessible via DiagBox. Via Arduino I tried with Canhaker following a step by step guide from Vlud, but its software is not compatible with Continental's AIO and it didn't work either. I don't know which codes to try using Arduino, as I don't have that much knowledge. People who know how to change the VIN charge a lot for the service.
We don't always have the money for the service. I know you have to unlock the memory, but I don't know how...
-
Hi... I was researching the AIO Continental and found this forum... I would like to know if there is a way to change the VIN of the AIO Continental manufactured in Argentina? I want to install it in my car but it keeps beeping. Does anyone have any pointers on how to do this? thanks
