That's possible. Just like the fact that only diesel 180KM were in the GT
Beiträge von razor07b7
-
-
The GRIP control version has always been sold with 18" and M+S tires but GT have 19" and was not offered with GRIP control.
-
It depends on what version of the car you had. The GT version has a different sports button and does not have GRIP, even as an option. In this case there is no diagram or ready-made cables. You have to do it yourself, following the differences as above, but this should only be the case with the GT button. In the case of a standard one, it should be enough to replace the factory cable with a factory one with GRIP.
-
1640 is not directly connected to cirocco
PIN3 GND
PIN4 to BSI
PIN6 to BSI
1609 GT
PIN1 to PIN18 cirocco
PIN3 GND
PIN4 to BSI
PIN6 to PIN17 cirocco
yes normal sport switch have 3 wires and pin6 goes to BSI
PIN1 -> ICRA PIN8 -> cirocco PIN18
PIN3 -> ICRA PIN11 -> GND
PIN4 -> ICRA PIN1 -> BSI
PIN6 -> ICRA PIN9 -> cirocco PIN17
normal switch:
PIN3 -> ICRA PIN11 -> GND
PIN4 -> ICRA PIN1 -> BSI
PIN6 -> ICRA PIN18 -> BSI
if you want use new cable you have problem with pin6 because on ICRA pin18 or pin9 connect. you need to replace the connection from pin9 to pin18 in the new cable if you want to use the standard sport switch
-
PIN1 -> ICRA PIN8 -> cirocco PIN18
PIN3 -> ICRA PIN11 -> GND
PIN4 -> ICRA PIN1 -> BSI
PIN6 -> ICRA PIN9 -> cirocco PIN17
-
-
GT button has an additional diode on pin1 controlled from Cirocco
-
there are two sport buttons:
1) normal version
2) for GT
SPORT for GT code is 1609 colour green 6pin
1) addons pin1normal version is 1640
-
hello. I also need the pins of the 35-pin connector of the cable 98 355 847 80 that comes with star/stop and keyless closure
you need to check the diagram for this cable and your car on servicebox because there are different versions
-
this is not entirely true ...
My ESP90 as if it were ESP81
CodeF080 >> 62F080982554978000039812786180FFFFFFFF1101FFFFFF01 F0FE >> 62F0FE0000000003920F0111030A1403FFFFFF0002000001926615
and after try unlocking with 60A5 receive an answer 7F2735 (error code wrong unlock key)
with key ABFB my ESP90 is working
-
Hello everyone,
I want to activate Grip Control and Hill Descent Control in my 5008 II.
My current settings in ESP 90:
2101 - 06 BF FF FF FF FF FF FD FF FF FF FF FF EF FF FF FF FF FB 7F FF EF FF FF EF BA AE FF
What value should I change?
EF -> ?
BA -> ?
EF -> EE
BA -> 3A
-
I don't think there is a zone in BSI to turn it on
It seems to me that this option, if available in the 3008, will only be available in the facelift after 2020
-
Peugeot 3008 II GT BlueHDI 180 12.2018
Der schwarze 35PIN in Richtung BSI hat 18 Kabel, aber eine andere Anordnung als ich hier gesehen habe.
Kabel im tunel : 9814520480 foto unten.Bis auf das neue Kabel habe ich schon alles . Das Kabel 9814520580 wird nicht geeignet sein ?
PINOUT CABLE factory installed: 9814520480
two wires shorted: white and yellow/green to BLACK 35PIN connector.
This 35PIN connector has 17 pins connected but 35PIN connector to BSI has 18 pin/wires connected. This one is unused through this cable 9814520480. This PIN is 18 - green wire
-
I'll copy the content here to the thread:
Check zone 23EE on BSI:
>752:652
1003
2223EE
6223EE....
I assume you will have a value of 1
this zone have description: Dynamic driving function and value:
0 - absent
1 - global
2 - partial. Only engine control and gearbox
maybe the value 2 will result in only engine and transmission control remaining
:B4E0:03:03
2E23EE02
2E2901FD000000010101
1001
there is one more zone 2499 on BSI
2499 - The operating mode of the steering and depreciation of the car Value:
0 - normal mode of operation
1 - sports operating mode
next zone 23DA on BSI:
The presence of dynamic driving function value:
0 - absent
1 - present
but I don't know what the change will do.
Test and return to previous value.
-
Yes new topic:
Dynamic driving function and Sport mode -
Check zone 23EE on BSI:
>752:652
1003
2223EE
6223EE....
I assume you will have a value of 1
this zone have description: Dynamic driving function and value:
0 - absent
1 - global
2 - partial. Only engine control and gearbox
maybe the value 2 will result in only engine and transmission control remaining
:B4E0:03:03
2E23EE02
2E2901FD000000010101
1001
there is one more zone 2499 on BSI
2499 - The operating mode of the steering and depreciation of the car Value:
0 - normal mode of operation
1 - sports operating mode
next zone 23DA on BSI:
The presence of dynamic driving function value:
0 - absent
1 - present
but I don't know what the change will do.
Test and return to previous value.
-
I'm glad it worked !
It depends on what is already active and what can still be activated in a specific car.
-
No. No. No. 5 second is only after unlocking command :B4E0:03:03
>752:652 - this line is the ID selection for RX and TX to communicate with the ECU (in this case is BSI)
1003 - open communication session with the selected above ECU22234C - 22 zone (22 234C) - 22 is read command from zone 22xxxx - in this case a reading from 234C
62234C00 - 62 zone value (62 234C 00) - 62 is answer command from ECU for zone 234C - value is 00
BSI Zone 234C - Driver Welcome value
0 - disabled
1 - enabled
to write in the zone we must have the ECU unlocked
:B4E0:03:03 - this command unlock the BSI for writing in the zone
after type enter, there is a maximum of 5 seconds to type the next command below - write to the zone
2E234C01 - 2E zone value (2E 234C 01) - 2E is write command to zone 234C value 01
2E2901FD000000010101 - 2E is write command to zone 2901 value FD000000010101 for secured traceability
1001 - close communication session with the selected ECU
-
Yes, exactly.
First from the console Arduino IDE and coding BSI commands as above
then use the tool for NAC/CIROCCO and insert new option in zone 2127 -> driver welcome
Remember you have max 5 seconds after typing
:B4E0:03:03next line
so that there are no interruptions in typing the next lines
So it is a good idea to type: :B4E0:03:03 in the console and do not confirm ENTER and copy the next line to the clipboard.
This will speed up typing next lines on the console
correctly performed BSI coding will show the value 1 in zone 234C:
>752:652
1003
22234C
62234C01
-
Ich verwende Diagbox nicht für die BSI-Codierung.
Sowohl für BSI als auch für NAC verwende ich das Arduino Uno + Can-Bus MCP2515-Modul.
für BSI auf Arduino hochgeladen - https://github.com/ludwig-v/arduino-psa-diag/
Die Codierung erfolgt auf der Arduino COM-Konsole
für NAC mit Arduino : https://github.com/ludwig-v/arduino-psa-nac_rcc_cirocco
Deutsch ist nicht meine Muttersprache, ich benutze einen Übersetzer