Hello partners. Let me tell you that I solved the problem with the sport button just as Razor told me. I put the normal sport button configuration on the new cable, summarizing in black block I changed pins 9 for pins 18. Solved.
Beiträge von deloco2
-
-
It's really driving me crazy. If I put my old cable that is modified with grip, putting pin 1 of the sport button on pin 8 of the black block, the sport button works with a red light but not the grip control. Then if I put in the new cable the grip control works but not the sport button. new cable comes with pins 8 and 9 to the black block. what madness!!!!
-
Could you send me the two complete diagrams? please.
-
That is the idea to change pin 9 to 18, which is why I asked you. thank you so much.
pd: I really ridiculous about this button to do the same thing, what a way to complicate it.
-
Well I don't understand it, what madness!!! On my car cable there are the two pins as you can see in the previous photo that I posted. both pin8 and 9 and it doesn't work. However, I put my old cable back in and the normal button works. Could you tell me on the normal button, pin 6 goes to bsi pins go to the black block?
-
Could you tell me if the pin that goes to pin 17 of the cirocco is in the black block, since I understand that pin 6 is there and I don't know which one it is in the black block either. the idea to be able to change pin 6 from bsi to cirocco on the black block.
-
Do you have the entire diagrams for each button to know which pins it goes to in the ciroco? Razor07b7
-
It could then be activated with the Ludwig application. psa arduino cirocco? Or do I disconnect pin 1 on very bad occasions?
-
Okay, that's what I understand, thank you. But my problem is that my car comes with a normal sport button and when I bought the cable for grip control it comes with the sport GT button. I have the cable and the GT button but it doesn't work. So I don't know if you have to put some coding to change it from normal to gt?
-
hello. Could you give me the coding for the sport button with light, the cable I bought comes with it and my old one doesn't. I connect it and it doesn't work. Thanks in advance
-
Hallo. Kann mir jemand später bei der Installation der 230-V-Steckdose für den Peugeot 5008 von 2019 helfen? Könnten Sie mir den Schaltplan schicken? Ich habe die Konsole zerlegt und kann den 3-poligen Stecker, der in dem von mir gekauften Kit enthalten ist, nicht finden. Vielen Dank.
Die Kit-Referenz ist das, was ich in das Bild eingefügt habe. und das Folgende ist der Stecker, den ich nicht in meinem Kabelbaum habe
-
-
In the photo I attached, it is assumed that I have correctly unlocked the ecu, right, is that correct?
but nevertheless I immediately go to diagbox and I get an internet error as you can see in photo 2.
-
mittins. Yesterday I tried to use your program and I didn't do something right. Being in diagbox I enter bsi then in repair and I put it in coding with visualization, then I go to your program I look for a key and I put it in the last tab and I click on unlock ecu, I immediately go back to dicebox and I click on code, but I get that it has not been connected to the internet.
-
I have to enter the diagbox inside the ecu to where it says: "coding with visualization"?
-
And 240E ?It sets alarm architecture for this, what should I set?
-
I have seen it, which is why I am asking to know if I have to activate it, since I have install the alarm.
-
I don't understand what thatcham mode is, in code 2365 and 240E either. Let's see if someone can clarify for me. The photo is forum peugeot
-
-
hello. I also need the pins of the 35-pin connector of the cable 98 355 847 80 that comes with star/stop and keyless closure