Beiträge von akn33

Siberiak No i didnt manage to connect. It is need engine ecu when connecting.

Thank you so much for your reply.

Hmmmm. I know 23EE.

My 23EE now 2 (default form factory) . If i set to global (1) , my sport button and eco mode button not working.

C5 Aircross 1.5 Bluehdi 130 hp.

Zitat von Futee79

Hello Friemds

meanwhile my Dynamic Sport Pack it is working, i need to use another setting in BSI

the only annoying thing is that stupid sound in sport mode, and i can not turn it off ( i tried almost all settings)

I tried these ones, without luck

set the DSP sound efficiency from 1 to 0

set the DX law from 1 to zero

any advice guys?

Thank you

Alles anzeigen

Hi,

Which menus did you activate? BSI , Engine or ???

I see on my cirocco but not working.

Thank you

Hi Mittns . Thanks for guides.

What do you think about this nac? 9832991580

This is Wave 4 and HD version. My car is C5 Aircross. 12 inch tft dashboard screen and 8 inch HD console screen. Does it work without problems?

If you had to choose between these two, which would you get?

9832991580 and 9820225580

Hi Guys, How are you ?

Where or how can i find delphi EI5 bsi calibration file?

Delphi EI5 BSI .

HW-9830813080 SW-9693952280

Hi,

I did try again. This table is my pin out scheme from psa sheme.

I still couldn't connect.

Communication error.

Although I provided all the connections according to the specified scheme, unfortunately I could not get any results.

By the way, when I connect the ABS pump to the vehicle, there is no problem. I can see it directly over the DB.

Sorry, the attached ABS file is in Turkish.

a" 46-track black socket

End number Description

1 Plus supply of the electric motor of the hydraulic pump to the distribution battery

2 Supply of right rear brake caliper motor

3 Feed return of the right rear brake caliper motor

4 CAN HS 1 High

5 CAN HS 1 High

6 Unconnected end

7 Left front wheel speed signal

8 Unconnected end

9 Unconnected end

10 Unconnected end

11 CAN HS 2 High

12 Feed return of the left rear brake caliper motor

13 Supply of left rear brake caliper motor

14 Electrical chassis

15 Electric parking brake 2 actuation

16 Electric parking brake 4 control

17 Unconnected end

18 CAN HS 1 Low

19 CAN HS 1 Low

20 Unconnected end

21 Right front wheel speed signal reference

22 Right rear wheel speed signal reference

23 Left rear wheel speed signal

24 Left front wheel speed signal reference

25 CAN HS 2 Low

26 Right front wheel speed signal

27 Unconnected end

28 Unconnected end

29 Unconnected end

30 Distribution battery positive supply of electronic control unit

31 Electric parking brake 1 control

32 Electric parking brake 3 control

33 Unconnected end

34 Status assurance wired information of vehicle movement

35 Information about vehicle speed

36 Remote control brain standby information

37 Right rear wheel speed signal

38 Unconnected end

39 Left rear wheel speed signal reference

40 Unconnected end

41 Brake fluid level information

42 Unconnected end

43 Unconnected end

44 Unconnected end

45 Unconnected end

46 Electrical chassis

Hi everybody ,

I have got EL5 BSI . I working on table without any problems.

I want to connect my ESP90 unit(9808958280) to bsi but Diagbox not shown. I cant connect to esp with arduino either.

I have got esp and bsi connection scheme. But i cant contact to esp.

How can i connect to esp on table?

If you have diagbox virtual (above 9.80) and lexia , you will close economy mode for one hour.

BSI > Maintenance-BSI functioning mode > BSI functioning mode > Exit economy mode