[NAC] (Wave 3) System - Technische Infos

  • Da ich bald beim Wave 2 gegen Wave 3 tausche, nutze ich mal die Gelegenheit, ein paar Informationen zu der Hardware zu veröffentlichen.

    Im Netz findet man ja absolut nichts dazu.



    Hier ein paar grundlegende Daten:


    • Teilenummer: 9830039180 (mit DAB+)
    • Hersteller: Continental
    • Model: NAC EUR wave3 / W3_EU_B2DAB
    • Hardware Revision: D3
    • Herstellungsdatum: 18.09.2018
    • Software (Auslieferungszustand): 31.08.05.86
    • FCC ID: ZFW-NACEUR3


    Nun zu den inneren Werten, die ich anhand der verlöteten Chips rausgesucht habe:


    • CPU: Arm Cortex-A9 4x1,0 Ghz (Bez. MCIMX6Q6AVT10AD SBCA1825) (Derselbe wie im Wave 2)
    • Ram: 4x 256MB DDR3L SDRAM 933Mhz (Bez. D9SHM)
    • Speicher:
    1. SEC 749 B03P KLMBC4GESD (Größe: unbekannt)
    2. Flash Speicher von Micron mit Bez. 29F8G08ABACA (Größe: 8GB)
    3. Flash Speicher 32MB MX25l3235EMR-10G
    • Audio Prozessor: SAF7755HV/205
    • Digital Verstärker: TAS514CT01 von Texas Instruments
    • Video Decoder/Konverter: ADV7182 WBCS
    • Serializer mit LVDS Interface: MAX9277 GTM/V
    • USB Controller Hub: SMSC USB84604 (Unterstützung für 4 Ports)
    • Wifi/Bluetooth Chip: Wifi 2,4Ghz & 5Ghz a,b,g,n. inkl. Wifi-Direct Support / Bluetooth 4.1 (Bez. CSRC9300)
    • Lüfter: ASB0412MA DC12V 0,10A von Delta Electronics (Auch unter anderen Herstellernamen zu finden für ca. 5€)

      Der Lüfter befindet sich von vorne gesehen auf der linken Seite.


    Und hier die Anschluss Codierungen:


    • FAKRA A (Schwarz): LVDS
    • FAKRA B (Weiß): FM/AM Antenne
    • FAKRA C (Blau): GPS Antenne
    • FAKRA E (Grün): USB/SOS BTA System
    • FAKRA M (Orange): DAB+ Antenne
    • FAKRA Z (Hellblau/Wasserblau): USB


    Wenn ich mehr herausfinde, ergänze ich die Daten noch.

    Und hier mal ein paar Bilder:








    Letzte Änderung: 05.06.2021

    308 GTi (╯°□°)╯︵ ┻━┻

    Einmal editiert, zuletzt von Mittns ()

  • HiMittns!

    Where do you buy this device ? And can install an operating system other than NAC??

    Your future depends on many things, but mostly on you :writing_hand: :folded_hands:

    :red_heart: :red_heart: Peugeot 3008 2018 :red_heart: :red_heart:

  • Where do you buy this device ?

    Allegro.pl.

    Sometimes there are many offers. :)


    And can install an operating system other than NAC??

    You mean in the car itself or an os in the nac?

  • Thank you so much for your information !

    I think this chipset might be suitable for another OS (eg Android)

    Can I post link on this post ? (community.nxp.com/t5/i-MX-Processors/android-build-fails-for-MX-O8-0-0-1-sabresd-6dq-userdebug/m-p/818575)

    Your future depends on many things, but mostly on you :writing_hand: :folded_hands:

    :red_heart: :red_heart: Peugeot 3008 2018 :red_heart: :red_heart:

  • Technically it could be possible, but you have to develop a new firmware with all drivers for the other chips.

    And don't forget, that it is only a slow quadcore. ^^

    Even a slim Android rom would run slow.

    And then this super slow 933mhz ram.


    I bet it would run half as slow as a Raspberry 3 with android rom.

    It would be ideal if you could connect an old smartphone via USB and completely mirror the surface.


    At least, compared to the wave 2, the ram of the wave 3 is a little bit faster (+133mhz).

  • Hallo Mittns,

    Das gleiche Radio ist auch in den neueren,

    Opel modellen eingebaut.

    Weißt du zufällig ob auf dem Radio auch din vin abgelegt wird.


    Ich habe heute schon versucht das Radio auf der Werkbank zum laufen zu bekommen, nur leider wird es nicht mit GDS2 und einen MDI2 nicht erkannt.


    Verkabelt habe ich so

    PIN 11 (12 volt)

    PIN 22 (Masse)

    PIN 10 (Can-bus +)

    PIN 22 (Can-bus -)


    Im Anhang habe ich die komplette stecker belegung.


    Danke und Gruß

    Mark

  • Weißt du zufällig ob auf dem Radio auch din vin abgelegt wird.

    Jepp, die wird auch im Radio abgelegt.


    Ich habe heute schon versucht das Radio auf der Werkbank zum laufen zu bekommen, nur leider wird es nicht mit GDS2 und einen MDI2 nicht erkannt.

    Das Radio schaltet nur ein, wenn es vom Zentralsteuergerät den Bus Befehl zum einschalten bekommt.

    (Zündung einschalten)




    Beim Peugeot ist es das BSI.

    Wie es beim Opel genannt wird, weiß ich leider nicht.

  • Bei Opel wird es das BCM sein.

    Wenn ich es über das BCM verbinden kann ich es dann auch über can für anderw Fahrzeuge vorbereiten?

    Das das NAC plag and play verbaut werden kann?

  • Wenn ich es über das BCM verbinden kann ich es dann auch über can für anderw Fahrzeuge vorbereiten?

    Nimm es mir nicht übel, aber ich unterstütze keine Kommerzialisierung... ;)

  • Nein, das nehme ich dir nicht über vllt.

    habe ich mich da nur falsch ausgedrückt.

    Ich möchte dieses System in meinem Opel Astra verbauen, dieses ist ja auch in den facelift Modellen drin.

    Nur ich habe echt schlechte Erfahrungen damit gemacht direkt am Auto am bcm (BSI)

    Zu programmieren.

    Geht was schief ist die wegfahsperre aktiv. Deswegen würde ich es lieber versuchen im Keller zu konfigurieren.

    Und dann später versuchen es plug and play im meinem Auto zum laufen zu bekommen.

    Und da mein Auto seit 2018 keine kartenupdates mehr bekommt muss ich halt eine Alternative her und ich bin da sehr experimentierfreudig nach dem Motto geht nicht gibt's nicht.

  • Am BSI (sofern nicht uralt) braucht man i.d.R. nichts machen.

    Es ist quasi Plug&Play, wenn das Nac konfiguriert ist.


    Es gibt im BSI zwar den Punkt, um das angeschlosse Infotainment System auszuwählen, bringt aber keinen Unterschied, soweit ich das festgestellt hab.

    Bei mir steht es sogar immer noch auf "Smeg".


    ich bin da sehr experimentierfreudig nach dem Motto geht nicht gibt's nicht.

    So lob ich mir das. :OK_hand: 8)



    Wenn du damit anfängst, würde ich aber vorschlagen, es hier im User Projekte Forum in einem neuen Thread zu bequatschen, da wir schon jetzt vom Thread hier abweichen.

  • Wenn du damit anfängst, würde ich aber vorschlagen, es hier im User Projekte Forum in einem neuen Thread zu bequatschen, da wir schon jetzt vom Thread hier abweichen.

    Ja, mach nen Userprojekt draus, das Navi 900 ist ja quasi seit Erscheinen tot.

    Wir haben nen 1.6er 100kw aus 01/17.

    Mich ärgert alleine das das Theater um die Karten ungemein.

  • I make an update and a clarification on the type of ram and the speeds (material taken from the original datasheets)


    The size of the memories is like on wave2 256mb x 4 = 1gb total with CL13 speed (DDR3 1866)


    Strange thing, and correct me if I'm wrong, is the processor, from the datasheet it emerges that it accepts maximum speed of 532mhz for DDR3L memory

    So the speed of wave3 is not given by the ram memory, but by the type of flash rom and storage optimization

  • material taken from the original datasheets

    Psa internal datasheets or do you mean the micron datasheet?


    I wasn't quite sure about the speed as there are 6 different speeds (800, 1066, 1333, 1600, 1866, 2133) of the ram.

    I found datasheets for the designation "D9QBB" but less for "D9SHM".



    Strange thing, and correct me if I'm wrong, is the processor, from the datasheet it emerges that it accepts maximum speed of 532mhz for DDR3L memory

    Hmm, i'm not sure.

    That would mean that the cpu only uses about 1/3 of the speed of the rams? :/

  • material taken from the original datasheets

    Psa internal datasheets or do you mean the micron datasheet?


    I wasn't quite sure about the speed as there are 6 different speeds (800, 1066, 1333, 1600, 1866, 2133) of the ram.

    I found datasheets for the designation "D9QBB" but less for "D9SHM".

    Yes, micron datasheet, D9QBB and D9SHM are the same type of memory, the code difference is for the speed difference

  • Doesn't mean that the ram should have an effect on the system speed (if both are not throttled to the same clock speed), as i said?

  • Theoretically if the processor accepts those speeds yes, while if the processor accepts a maximum of 532mhz the memories do not affect.


    Not sure about the processor

  • Otherwise there would be no point for me to build another Ram with more speed.

    Or even a ram that is clocked >600 mhz.

    Maybe the pdf is not accurat enough (informations too old?) or there are newer iMX models that can handle more speed, i'm also not sure.

  • I don't think there is an updated version of this processor, the datasheet comes from the official website of the NXP manufacturer, and it is specified that it supports DDR3L 1066 (532mhz) memory.


    I also note that, in the discussion of the versions, wave2 with dab has different from wave3 only the flash rom size, so in theory the firmware of w3 could be injected in w2

  • Ja Wahnsinn, das sind mal Detailinformationen! Bin seit Ewigkeiten auf der Suche nach der Steckerbelegung vom wave gewesen...

Jetzt mitmachen!

Hey! Es scheint, als ob Dir dieser Austausch gefällt, aber Du hast bisher noch kein Benutzerkonto erstellt. Mit einem Konto kannst Du über neue Antworten informiert werden, Foto's in unsere Galerie hochladen, unsere Tools nutzen, anderen mit einem „Gefällt mir“ danken oder selbst dabei unterstützen, anderen zu helfen. Gemeinsam können wir dazu beitragen, diese Community zu etwas größerem zu machen.